Resistor Noise

Due to the random thermal motion of charge carriers, we get thermal noise, and we observe it as voltage and current noise in resistive circuit elements that is proportional to absolute temperature. We expect this to be the case since at higher temperatures, electrons and holes have higher energy, leading to larger instantaneous velocities, and larger excursions from the drift velocity due to an electric field.

Modeling Thermal Noise in Resistors

Consider the noisy resistor in Fig. 1. We can model this as a noiseless resistor in series with a voltage noise generator, or a noiseless resistor in parallel with a current noise generator. Since we cannot predict the voltage or current noise at any point in time, we instead specify the noise voltage or current power:

${\overline {v_{n}^{2}}}=4kTRB$

(1)

${\overline {i_{n}^{2}}}=4kTGB={\frac {4kTB}{R}}$

(2)

Where $k$ is Boltzmann's constant, equal to $8.617\times 10^{-5}\mathrm {\tfrac {eV}{K}}$, and $B$ is the observation bandwidth. Thermal noise is white noise, hence the noise generators have white power spectral densities, as shown in Fig. 2. Just like any small signal, the shape of the power spectral density can be shaped by the frequency response of the rest of the circuit.

Also note that the polarity of the noise generators are intentionally not specified in the symbols, since the noise voltage or current can take on positive or negative values at any given time.

For example, a resistor with $R=10\mathrm {k\Omega }$ at $T=20^{\circ }C=293K$, the voltage noise power is:

${\overline {v_{n}^{2}}}=4kTRB=1.62\times 10^{-16}\cdot B$

(3)

Which gives us:

$v_{\mathrm {n,rms} }={\sqrt {\overline {v_{n}^{2}}}}={\sqrt {4kTRB}}=1.27\times 10^{-8}\cdot {\sqrt {B}}$

(4)

For a measurement bandwidth of $B=1\mathrm {MHz}$, we get $v_{\mathrm {n,rms} }=13\,\mathrm {\mu V}$. This is the smallest voltage, or the minimum detectable signal we can resolve across this resistor with this bandwidth, i.e. the smallest voltage we can distinguish from the thermal noise of the resistor.

Noise in Resistor Circuits

Consider two noisy resistors in series, as shown in Fig. 3. The equivalent resistance of the series circuit is $R=R_{1}+R_{2}$, and since we can sum the voltage noise powers, we get:

${\overline {v_{n}^{2}}}={\overline {v_{n1}^{2}}}+{\overline {v_{n2}^{2}}}=4kTR_{1}B+4kTR_{1}B=4kT\left(R_{1}+R_{2}\right)B=4kTRB$

(5)

It is important to remember that the noise power is additive, but the noise voltages and currents are not, since we do not know the phase of these signals at a given point in time. Similarly, for the parallel resistor circuit in Fig. 4, the equivalent conductance is $G=G_{1}+G_{2}$, and the resulting equivalent current noise generator is:

${\overline {i_{n}^{2}}}={\overline {i_{n1}^{2}}}+{\overline {i_{n2}^{2}}}=4kTG_{1}B+4kTG_{1}B=4kT\left(G_{1}+G_{2}\right)B=4kTGB$

(6)

In adding the noise powers, we assumed that the noise generators are independent of each other, i.e. the noise sources are uncorrelated. We will look at the case of correlated noise sources later.