Difference between revisions of "Noise in RF Circuits"

From Microlab Classes
Jump to navigation Jump to search
Line 56: Line 56:
  
 
=== Amplifier Noise Figure ===
 
=== Amplifier Noise Figure ===
 +
Consider the amplifier model in Fig. 4, with input signal <math>S_i</mathrm>, power gain <math>G</math>, and output signal <math>S_o</math>. If the power of the input signal is <math>P_\mathrm{signal}</math>, and <math>N_S</math> is the noise power at the input, we can write the input SNR as:
 +
 +
{{NumBlk|::|<math>\mathrm{SNR_{in}}=\frac{P_\mathrm{signal}}{N_S}</math>|{{EquationRef|9}}}}
 +
 +
Since amplifier will amplify both the signal and the noise, the output SNR is then:
 +
 +
{{NumBlk|::|<math>\mathrm{SNR_{out}}=\frac{G\cdot P_\mathrm{signal}}{G\cdot N_S + N_\mathrm{amp,o}} = \frac{P_\mathrm{signal}}{N_S + \frac{N_\mathrm{amp,o}}{G}</math>|{{EquationRef|10}}}}
 +
 +
Where <math>N_\mathrm{amp,o}</math> is the noise power at the output of the amplifier when there is no input.
  
 
=== Noise Figure of Cascaded Blocks ===
 
=== Noise Figure of Cascaded Blocks ===

Revision as of 18:46, 4 October 2020

In this module, we consider the noise generated by the electronic devices themselves due to the (1) random motion of electrons due to thermal energy and (2) the discreteness of electric charge. We see this as thermal noise in resistances, and shot noise in PN junctions. In MOS transistors, we also see flicker noise. This noise is not fundamental, but is due to the way MOS transistors are manufactured, This added uncertainty in the voltages and currents limit the smallest signal amplitude or power that our circuits can detect and/or process, limiting the transmission range and power requirements for reliable communications.

Modeling Noise

Figure 1: Random movement of an electron in an electric field.

Since electronic noise is random, we cannot predict its value at any given time. However, we can describe noise in terms of its aggregate characteristics or statistics, such as its probability distribution function (pdf). As expected from the Central Limit Theorem, the pdf of the random movement of many electrons would approach a Gaussian distribution with zero mean since the electrons will move around instantaneously, but without any excitation, it will, on the average, stay in the same point in space. If we add an electric field, then the electron will move with an average drift velocity, , but at any point in time, it would be moving with an instantaneous velocity , as shown in Fig. 1. Note that is the electron mobility.

Noise Power

Aside from the mean, to describe a zero-mean Gaussian random variable, , we need the variance, , or the mean of . For random voltages or currents, , this is equal to the average power over time, normalized to :

 

 

 

 

(1)

Figure 2: Zero-mean noise signals in time with different variances.

Thus, to describe noise, we can use its variance, or equivalently its average power. Fig. 2 illustrates the difference between two noise signals with different variances. Recall that , the square root of the variance, is the standard deviation.

Consider a noise voltage in time, , similar to the ones depicted in Fig. 2. The mean is then:

 

 

 

 

(2)

The variance, however, is non-zero:

 

 

 

 

(3)

We can also calculate the root-mean-square or RMS as:

 

 

 

 

(4)

Noise Power Spectrum

We can also examine the noise in the frequency domain, specifically, how noise power is distributed over frequency. Many noise sources are white, i.e. the noise power is distributed evenly across all frequencies, as seen in Fig. 3. Thus, white noise is totally unpredictable in time since there is no correlation between the noise at time and the noise at time , no matter how small is, since the likelihood of a high frequency change (small ) and a low frequency change (large ) are the same.

The noise power should be the same, whether we obtain it from the time or frequency domain, we can then write:

 

 

 

 

(5)

Where is the noise power spectral density in . An alternate representation of the noise spectrum is the root spectral density, , with units of .

Noise in Communication Systems

Noise is present in all parts of a communication system. In analog systems, it reduces the quality of the received signal, e.g. introducing static sounds in audio signals, or "snow" in television images. In digital systems, it degrades throughput, e.g. due to retransmissions caused by packet errors or the due to the extra coding needed to recover data in the presence of errors.

Signal-to-Noise Ratio

In general, we try to maximize the signal-to-noise ratio (SNR) in a communication system. For an average signal power , and an average noise power , the SNR in dB is defined as:

 

 

 

 

(6)

Again note that we are referring to random noise and not interference or distortion.

Noise Figure

The noise figure (NF) measures the degradation of SNR in a circuit or block. The noise figure is defined as:

 

 

 

 

(7)

Expressed in dB, we get:

 

 

 

 

(8)

We use and to distinguish between the dB and non-dB values of noise figure. Note that some texts call the noise factor. In measuring or calculating the noise figure, we specify a standard input noise level, generated by a source resistance, , at a set temperature. For example, in RF systems, we typically set and .

Amplifier Noise Figure

Consider the amplifier model in Fig. 4, with input signal , and output signal . If the power of the input signal is , and is the noise power at the input, we can write the input SNR as:

 

 

 

 

(9)

Since amplifier will amplify both the signal and the noise, the output SNR is then:

 

 

 

 

(10)

Where is the noise power at the output of the amplifier when there is no input.

Noise Figure of Cascaded Blocks