EEE 51 Transistor Models

In EEE 41, you studied the fundamental concepts of how transistors can be realized using semiconductors, specifically, the two most popular transistors currently in use: the bipolar junction transistor (BJT) and the metal-oxide field-effect transistor (MOSFET).

In EEE 51, we want to be able to use these transistors (as well as other semiconductor devices such as diodes) to design and implement useful electronic circuits. This means we have to be able to describe, and eventually predict, the behavior of the terminal voltages and currents of these devices. We can accomplish this by using transistor models.

Large Signal Transistor Models

The large signal transistor models allow us to describe the electrical behavior of the transistor, when a voltage or current is varied over its allowable range. Here, we can see how varying the terminal voltages (and currents) determine the operating region of the transistor. Since there are many combinations of voltages and currents available for us to choose from, it is convenient to standardize which terminal voltages/currents we can use. This makes it easy to compare different transistors, as well as to systematically analyze and design electronic circuits based on these transistors.

The standard large signal transistor characteristics that we use are (1) the transfer characteristics, (2) the output characteristics, and (3) the input characteristics. Note that these models are normally considered as DC or low-frequency models, where we assume that the transistor parasitic capacitances are still negligible.

Transfer Characteristics

Transfer characteristics usually implies an input-output relationship, similar to the transfer function of a two-port network. But where are the input/output terminals or ports of a transistor? As we will see later on, one of the main goals of electronic circuits is to amplify signals (i.e. voltage, current, etc). Thus, it is convenient to choose the input-output terminal pair of a transistor that is commonly used to provide the largest amplification. In the BJT case, it is the common-emitter configuration, and in the MOSFET case, it is the common-source configuration.

The BJT Transfer Characteristic

Figure 1: The BJT common-emitter configuration.

The BJT common-emitter (CE) configuration is shown in Fig. 1. We define the “input” signal as the base-emitter voltage, $V_{BE}$, and the “output” signal as the collector current $I_{C}$. Therefore, we can model the the BJT transfer characteristic using

$I_{C}=I_{S}\cdot \left(e^{\frac {V_{BE}}{n\cdot V_{T}}}-1\right)\cdot \left(1+{\frac {V_{CE}}{\left|V_{A}\right|}}\right)$

(1)

for a transistor in the forward-active region. Note that $I_{S}$ is the reverse saturation current of the collector-base junction and dependent on the type and geometry of the transistor, $n$ is the ideality factor, accounting for recombination in the base-emitter junction, $V_{A}$ is the Early Voltage, and $V_{T}={\tfrac {kT}{q}}$, the voltage equivalent of temperature ($V_{T}=26\,\mathrm {mV}$ at $T=300\,\mathrm {K}$). For typical discrete (not integrated) BJTs, the value of $V_{BE}$ is around $0.65\,\mathrm {V} \sim 0.75\,\mathrm {V}$, and since $V_{A}$ is typically much greater than $V_{CE}$, we can simplify Eq. (1) into

$I_{C}\approx I_{S}\cdot e^{\frac {V_{BE}}{n\cdot V_{T}}}$

(2)

Eq. (1), shown in Fig. 2, and superimposed with the transfer characteristic of the 2N2222A NPN BJT, allows us to approximate the behavior of the “output” signal, in this case the collector current, when we change the base-emitter voltage, our “input” signal.

Figure 2: The BJT transfer characteristics of a 2N2222A NPN transistor.

The MOSFET Transfer Characteristic

The MOSFET common-source (CS) configuration is shown in Fig. 3. As with the BJT, we define the “input” signal as the gate-source voltage, $V_{GS}$, and the “output” signal as the drain current, $I_{D}$. Thus, the MOSFET transfer characteristic can be modeled as

$I_{D}=k\cdot \left(V_{GS}-V_{TH}\right)^{2}\cdot \left(1+\lambda V_{DS}\right)$

(3)

in the saturation region. Note that $k$ is a constant dependent on the technology used in the manufacture, and the geometry, of the transistor, $V_{TH}$ is the transistor threshold voltage, and $\lambda$ is the channel length modulation coefficient. For typical discrete (not integrated) MOSFETs, $\lambda \ll 1$, allowing us to approximate Eq. (3) with

$I_{D}\approx k\cdot \left(V_{GS}-V_{TH}\right)^{2}$

(4)

And just like the BJT transfer characteristic, Eq. (3) allows us to model the behavior of the “output” signal, in this case the drain current, when we change the gate-source voltage, our “input” signal. Fig. 4 shows the transfer characteristic of a real MOSFET, together with the plot of Eq. (3).

Output Characteristics

In both the BJT and MOSFET, we defined our “output” as either the collector current or drain current. However, from Eqs. (1) and (3), we can see that both these “output” currents are also dependent on their respective “output” voltages -- the collector-emitter voltage, $V_{CE}$ for the BJT and the drain-source voltage, $V_{DS}$ for the MOSFET.

Since we want to be able to describe the transistor behavior completely, we need to take into account all the factors that affect the “output” current. Hence, we use the transistor output characteristic, $I_{C}$ vs. $V_{CE}$ for a BJT and $I_{D}$ vs. $V_{DS}$ for a MOSFET, to model the change in “output” current when the “output” voltage is changed.

The output characteristics of a typical BJT is shown in Fig. 5, and Fig. 6 shows the output characteristic of a typical MOSFET. Note that in both cases, the output characteristics span several operating regions. In the case of the BJT, the saturation, forward-active and cut-off regions can be seen. The same is true for the MOSFET, where the linear or ohmic region, the saturation region, and the sub-threshold region can be identified.

Input Characteristics

Since the BJT and MOSFET can be considered a three-terminal device, to completely describe all the currents and voltages, we will need 2 out of 3 voltages, and 2 out of 3 node currents. This means that in a BJT, if we know $V_{BE}$ and $V_{CE}$, we automatically know the value of $V_{BC}$ by KVL. By knowing the transfer and output characteristics, we can determine all the voltages in the BJT. The same is true for a MOSFET.

However, if we want to determine all the currents in the transistor, we need another set of current-voltage (I-V) characteristics. It turns out that the most convenient set of I-V characteristics for designing linear electronic amplifiers, is the “input” current vs. the “input” voltage characteristic. In BJTs, this is the $V_{BE}$ vs. $I_{B}$ characteristic, and for the MOSFET, this is the $V_{GS}$ vs. $I_{G}$ characteristic. For a BJT, by knowing $I_{B}$ and $I_{C}$, we can easily determine $I_{E}$ using KCL. Again, the same is true for MOSFETs.

The input characteristics of a BJT can be derived from the BJT transfer characteristics. Since $I_{B}={\tfrac {I_{C}}{\beta }}$, we can just divide the BJT transfer characteristic by the transistor $\beta$. The input characteristic of a MOSFET is trivial, since $I_{G}=0$.

In summary, these large signal models allow us to determine the resulting transistor “input” and “output” DC currents when we apply DC voltages across the transistor terminals. Since we can obtain the DC values of the currents and voltages in a transistor, the large signal transistor models are typically used in what is called “DC Analysis”.

Small-Signal Modeling

As we have just seen, semiconductor-based transistors are very nonlinear -- exponential behavior for BJTs and quadratic behavior for MOSFETs, and these nonlinearities can vary significantly when going from one operating region to another. Analyzing circuits with these devices, by hand, using these large signal models, becomes very complex very quickly, especially when the number of transistors start to increase. Imagine writing your node or loop equations with exponentials and quadratic functions!

In order to analyze, and eventually design, linear electronic circuits, we use two very powerful tools: linearization, and two-port network reduction. These two tools will allow us to (1) use our linear circuit theory skills (taken up in EEE 31 and 33), and (2) break up complex circuits into smaller and simpler ones.

Linearizing the Transistor Transfer Characteristic

In many cases, and often by design, the input signal of an amplifier is made to change by a relatively small amount on top of its DC value. To determine the effect of this disturbance on the rest of the terminal voltages and currents, we can use the large signal models. However, this would result in rather complicated mathematical expressions, with limited intuitive value. We will use the linearization process to reduce the complexity of the computation, as well as get a better intuitive grasp of the circuit implications, but at the cost of a certain amount of error.

Consider an NPN BJT, in the forward-active region, that is biased with a DC base-emitter voltage of $V_{BE,Q}$. This would result in a DC collector current $I_{C,Q}$, and from Eq. (2), is equal to

$I_{C,Q}=I_{S}\cdot e^{\frac {V_{BE,Q}}{V_{T}}}$

(5)

Note that we use the subscript Q to indicate that this is the quiescent point DC bias, meaning that this is the purely DC voltage and current of the BJT when there are no disturbances present.

Suppose we add a time-varying signal $v_{be}$ on top of $V_{BE,Q}$, such that the total base-emitter voltage is now

$v_{BE}=V_{BE,Q}+v_{be}$

(6)

Assuming that $v_{be}$ is small enough that the transistor does not change its operating region, the collector current then becomes

$i_{C}=I_{C,Q}+i_{c}=I_{S}\cdot e^{\frac {v_{BE}}{V_{T}}}=I_{S}\cdot e^{\frac {V_{BE,Q}+v_{be}}{V_{T}}}$

(7)

where $i_{c}$ is the collector current deviation away from its quiescent point, due to the addition of the “small” signal $v_{be}$. Simplifying Eq. (7), and using Eq. (5), we get

$I_{C,Q}+i_{c}=I_{S}\cdot e^{\frac {V_{BE,Q}}{V_{T}}}\cdot e^{\frac {v_{be}}{V_{T}}}=I_{C,Q}\cdot e^{\frac {v_{be}}{V_{T}}}$

(8)

As expected, $i_{c}$ is a nonlinear function (exponential) of $v_{be}$. Now, let us try to linearize this relationship. Here we present two methods, but as we will see, they turn out to be equivalent.

Method 1

Recall, that any function that is infinitely differentiable, can be expressed as an infinite sum of terms, and that these terms are calculated from its derivatives at a certain point. We call this infinite sum the Taylor Series representation of a function, such that

$f\left(x\right)=f\left(a\right)+{\frac {f'\left(a\right)}{1!}}\left(x-a\right)+{\frac {f''\left(a\right)}{2!}}\left(x-a\right)^{2}+{\frac {f'''\left(a\right)}{3!}}\left(x-a\right)^{3}+\ldots$

(9)

where the function $f\left(x\right)$ is expanded about point $a$. Expanding $f\left(x\right)=e^{x}$, about $a=0$, gives us the well known relationship

$e^{x}=e^{0}+{\frac {e^{0}}{1!}}x+{\frac {e^{0}}{2!}}x^{2}+{\frac {e^{0}}{3!}}x^{3}+\ldots =1+x+{\frac {x^{2}}{2!}}+{\frac {x^{3}}{3!}}+\ldots$

(10)

Thus, expanding $e^{\tfrac {v_{be}}{V_{T}}}$, we get

$e^{\frac {v_{be}}{V_{T}}}=1+{\frac {v_{be}}{V_{T}}}+{\frac {1}{2!}}\left({\frac {v_{be}}{V_{T}}}\right)^{2}+{\frac {1}{3!}}\left({\frac {v_{be}}{V_{T}}}\right)^{3}+\ldots$

(11)

Substituting Eq. (11) into Eq. (8) gives us

$I_{C,Q}+i_{c}=I_{C,Q}+{\frac {I_{C,Q}}{V_{T}}}v_{be}+{\frac {1}{2!}}I_{C,Q}\left({\frac {v_{be}}{V_{T}}}\right)^{2}+{\frac {1}{3!}}I_{C,Q}\left({\frac {v_{be}}{V_{T}}}\right)^{3}+\ldots$

(12)

We can remove the DC quiescent current term I_{C,Q} from both sides of Eq. (12), giving us

$i_{c}={\frac {I_{C,Q}}{V_{T}}}v_{be}+{\frac {1}{2!}}I_{C,Q}\left({\frac {v_{be}}{V_{T}}}\right)^{2}+{\frac {1}{3!}}I_{C,Q}\left({\frac {v_{be}}{V_{T}}}\right)^{3}+\ldots$

(13)